SOFControlV2
Discussion
THIS MODULE IS DEPRECATED AND NOT RECOMMENDED FOR NEW DESIGNS. PLEASE USE THE SOFControlV3 MODULE INSTEAD.
This module implements a general purpose second order filter that is capable of realizing many different filter types. The module performs internal smoothing allowing the filters to be updated without introducing clicks. In all cases, the module implements an underlying second order filter. First order filters are realized by setting some of the second order coefficients to zero.
The behavior of the cascade filters are controlled by the filterType arrary. The variable, filterType is an integer in the range from 0 to 22 inclusive.
After specifying filterType, adjust the filter parameters by setting the fields, gain, freq, and Q. Freq, gain and Q can be controlled either through respective input control pin or from the module inspector. Some filter parameters are not applicable to all filter types. The variable, freq controls the center frequency of the filter, gain determines the boost or cut in dB, and Q determines how sharp the filter is. Low Q values lead to broad filters and high Q values lead to narrow filters.
The following table discusses the various filter types and which variables are active in each case.
filterType=0, Simple pass through with unity gain.
filterType=1, Gain in dB. [gain].
filterType=2, 1st order Butterworth low pass filter. [freq].
filterType=3, 2nd order Butterworth low pass filter. [freq].
filterType=4, 1st order Butterworth high pass filter. [freq].
filterType=5, 2nd order Butterworth high pass filter. [freq].
filterType=6, 1st order allpass filter. [freq].
filterType=7, 2nd order allpass filter. [freq, Q].
filterType=8, 2nd order low shelf. It allows you to vary the gain of the low frequencies. The high frequencies have a gain of 1.0. [freq, gain].
filterType=9, 2nd order low shelf with Q. It allows you to vary the gain of the low frequencies. The high frequencies have a gain of 1.0. [freq, gain, Q].
filterType=10, 2nd order high shelf. It allows you to vary the gain of the high frequencies. The low frequencies have a gain of 1.0. [freq, gain].
filterType=11, 2nd order high shelf with Q. It allows you to vary the gain of the high frequencies. The low frequencies have a gain of 1.0. [freq, gain, Q].
filterType=12, 2nd order peaking filter. It has unity gain except around the specified frequency. By varying gain, you can get a peak or a notch in the frequency band. [freq, gain, Q].
filterType=13, 2nd order notch filter. It has unity gain except around the specified frequency. At the specified frequency, the filter has a true notch with -inf dB gain. [freq, Q].
filterType=14, 2nd order bandpass filter. It has unity gain at the specified frequency and falls off in both directions. The bandwidth of the filter is determined by Q. [freq, Q].
filterType=15, 1st order Bessel low pass filter. [freq].
filterType=16, 1st order Bessel high pass filter. [freq].
filterType=17, 1st order asymmetrical low shelf. [freq, gain].
filterType=18, 1st order asymmetrical high shelf. [freq, gain].
filterType=19, 1st order symmetrical low shelf. [freq, gain].
filterType=20, 1st order symmetrical high shelf. [freq, gain].
filterType=21, 2nd order Butterworth low pass filter with variable Q. [freq, Q].
filterType=22, 2nd order Butterworth high pass filter with variable Q. [freq, Q].
When the parameters freq, gain or Q are controlled through the input pin, then the default behaviour of the module is to calculate coefficients in the Set function. User can change the behaviour through the parameter setBehavior, to calculate coefficients in the Process function itself.
Module Pack
Advanced
ClassID
classID = 1415
Type Definition
typedef struct _ModuleSOFControlV2
{
ModuleInstanceDescriptor instance; // Common Audio Weaver module instance structure
INT32 filterType; // Selects the type of filter that is implemented by the module: Bypass=0, Gain=1, Butter1stLPF=2, Butter2ndLPF=3, Butter1stHPF=4, Butter2ndHPF=5, Allpass1st=6, Allpass2nd=7, Shelf2ndLow=8, Shelf2ndLowQ=9, Shelf2ndHigh=10, Shelf2ndHighQ=11, PeakEQ=12, Notch=13, Bandpass=14, Bessel1stLPF=15, Bessel1stHPF=16, AsymShelf1stLow=17, AsymShelf1stHigh=18, SymShelf1stLow=19, SymShelf1stHigh=20, VariableQLPF=21, VariableQHPF=22.
INT32 setBehavior; // Controls the Set function calling behavior of the module
FLOAT32 freq; // Cutoff frequency of the filter, in Hz.
FLOAT32 gain; // Amount of boost or cut to apply, in dB if applicable.
FLOAT32 Q; // Specifies the Q of the filter, if applicable.
FLOAT32 smoothingTime; // Time constant of the smoothing process.
INT32 updateActive; // Specifies whether the filter coefficients are updating (=1) or fixed (=0).
FLOAT32 b0; // Desired first numerator coefficient.
FLOAT32 b1; // Desired second numerator coefficient.
FLOAT32 b2; // Desired third numerator coefficient.
FLOAT32 a1; // Desired second denominator coefficient.
FLOAT32 a2; // Desired third denominator coefficient.
FLOAT32 current_b0; // Instantaneous first numerator coefficient.
FLOAT32 current_b1; // Instantaneous second numerator coefficient.
FLOAT32 current_b2; // Instantaneous third numerator coefficient.
FLOAT32 current_a1; // Instantaneous second denominator coefficient.
FLOAT32 current_a2; // Instantaneous third denominator coefficient.
FLOAT32 smoothingCoeff; // Smoothing coefficient. This is computed based on the smoothingTime, sample rate, and block size of the module.
UINT32 pinID; // Specifies which control pins are available.
FLOAT32* state; // State variables. 2 per channel.
} ModuleSOFControlV2Class;
Variables
Properties
| Name | Type | Usage | isHidden | Default Value | Range | Units |
|---|---|---|---|---|---|---|
| filterType | int | parameter | 0 | 0 | 0:22 | |
| setBehavior | int | parameter | 0 | 0 | 0:1 | |
| freq | float | state | 0 | 250 | 10:20000 | Hz |
| gain | float | state | 0 | 0 | -24:24 | dB |
| Q | float | state | 0 | 1 | 0.1:0.1:20 | |
| smoothingTime | float | parameter | 0 | 10 | 0:1000 | msec |
| updateActive | int | parameter | 1 | 1 | 0:1 | |
| b0 | float | derived | 1 | 1 | Unrestricted | |
| b1 | float | derived | 1 | 0 | Unrestricted | |
| b2 | float | derived | 1 | 0 | Unrestricted | |
| a1 | float | derived | 1 | 0 | Unrestricted | |
| a2 | float | derived | 1 | 0 | Unrestricted | |
| current_b0 | float | state | 1 | 1 | Unrestricted | |
| current_b1 | float | state | 1 | 0 | Unrestricted | |
| current_b2 | float | state | 1 | 0 | Unrestricted | |
| current_a1 | float | state | 1 | 0 | Unrestricted | |
| current_a2 | float | state | 1 | 0 | Unrestricted | |
| smoothingCoeff | float | derived | 1 | 0.06449 | Unrestricted | |
| pinID | uint | const | 1 | 7 | Unrestricted | |
| state | float* | state | 1 | [2 x 1] | Unrestricted |
Pins
Input Pins
| Name | freqPin |
| Description | Cutoff frequency of the filter |
| Data type | float |
| Channel range | 1 |
| Block size range | Unrestricted |
| Sample rate range | Unrestricted |
| Complex support | Real |
| Name | gainPin |
| Description | Gain of the filter |
| Data type | float |
| Channel range | 1 |
| Block size range | Unrestricted |
| Sample rate range | Unrestricted |
| Complex support | Real |
| Name | qPin |
| Description | Q of the filter |
| Data type | float |
| Channel range | 1 |
| Block size range | Unrestricted |
| Sample rate range | Unrestricted |
| Complex support | Real |
| Name | in |
| Description | audio input |
| Data type | float |
| Channel range | Unrestricted |
| Block size range | Unrestricted |
| Sample rate range | Unrestricted |
| Complex support | Real |
Output Pins
| Name | out |
| Description | audio output |
| Data Type | float |
Matlab Usage
File Name: sof_control_v2_module.m
M=sof_control_v2_module(NAME, FREQPIN, GAINPIN, QPIN)
Creates a general purpose second order filter that implements a number
of standard filter types. The filter operates on multiple interleaved
channels, with all channels being processed by the same set of
coefficients.
Arguments:
NAME - name of the module.
FREQPIN - Boolean that determines whether the module exposes an input pin that allows
the frequency of the filter to be adjusted.
GAINPIN - Boolean that determines whether the module exposes an input pin that allows
the gain of the filter to be adjusted.
QPIN - Boolean that determines whether the module exposes an input pin that allows
the Q of the filter to be adjusted.
Copyright (c) 2026 DSP Concepts, Inc.